Belgium
Pressure regulators Manifold
Series MD
With the Manifold version it is possible to realize a battery of regulators which are fed by a single source of inlet pressure.
Each regulator can be set up at any pressure (lower than the inlet pressure). The front or rear connection of each regulator allows to draw air at the pressure value set on the regulator itself.
Each regulator can be set up at any pressure (lower than the inlet pressure). The front or rear connection of each regulator allows to draw air at the pressure value set on the regulator itself.
Download catalogueSeries
Accessories
there are no salable codes online
If you have entered Filters, try changing them or look in the "Configurator" tab
Quantity added:
addtocart.popup.message.success
The requested quantity is partially confirmed
Product {0} is already in your cart with quantity {1}. You can update the quantity from cart page.
Product is not active
The product could not be added to the cart due to insufficient stock
Quantity must be greater than zero
Min allowed quantity for product {0} is {1}
Max allowed quantity for product {0} is {1}
Pack size for product {0} is {1}
It is not possible to add the product with code {0} to this cart
An error occurred, please try again later or contact customer support
Full screen
Quantity added:
addtocart.popup.message.success
The requested quantity is partially confirmed
Product {0} is already in your cart with quantity {1}. You can update the quantity from cart page.
Product is not active
The product could not be added to the cart due to insufficient stock
Quantity must be greater than zero
Min allowed quantity for product {0} is {1}
Max allowed quantity for product {0} is {1}
Pack size for product {0} is {1}
It is not possible to add the product with code {0} to this cart
An error occurred, please try again later or contact customer support
CODING EXAMPLE
| MD | 1 | R | T | 0 | 0 | 1/4 |
| MD | SERIES |
| 1 |
SIZE: 1 = 42 mm |
| R |
TYPE OF REGULATOR: R = pressure regulator M = Manifold pressure regulator |
| T |
OPERATING PRESSURE (1 bar = 14,5 psi): 0 = 0.5 ÷ 10 bar 2 = 0.5 ÷ 2 bar 4 = 0.5 ÷ 4 bar 7 = 0.5 ÷ 7 bar T = calibrated ** B = locked ** |
| 0 |
DESIGN TYPE: 0 = with relieving 1 = without relieving 2 = with relieving and by-pass valve (only for R regulator) 3 = without relieving, with by-pass valve (only for R regulator) |
| 0 |
PRESSURE GAUGE: 0 = without pressure gauge (with 1/8 port) |
| 1/4 |
PORTS (IN - OUT)*: = without cartridges 1/8 = G1/8 1/4 = G1/4 3/8 = G3/8 6 = tube Ø6 8 = tube Ø8 10 = tube Ø10 * NOTE: if the inlet (IN) cartridge is different from the outlet (OUT) cartridge, both dimensions shall be indicated. Example: MD1-R020-1/4-10 |
|
** NOTE: IF THE REGULATOR IS CALIBRATED OR LOCKED, AFTER THE PORTS ADD THE INLET PRESSURE “■” AND THE OUTLET PRESSURE “●” INLET PRESSURE: ■ = enter the SUPPLY pressure value OUTLET PRESSURE: ● = enter the OUTLET pressure value for the LOCKED regulator or the maximum value of the ADJUSTABLE pressure for the CALIBRATED regulator Example of a calibrated regulator with Inlet Pressure = 6.3 bar and Outlet Pressure = 4.5 bar Complete part number: MD1-RT00-1/4-6.3-4.5 |
Series MD pressure regulators - dimensions
There is no limit to the number of regulators that can be connected.
| Mod. | A | B | C | D | E | F | H | I | L | M | N | P | Q | R | S | T | U | V | W | Weight (kg) | Weight (kg) |
| MD1-M000 | - | G1/8 | 42 | Ø28 | 42 | M28x1,5 | 26,2 | 43 | Ø4 | 16 | 102 | 22,7 | 4 | 53,2 | 27 | 34,6 | 0 ÷ 11 | 10,5 | 48,8 | 0,2 | 0,2 |
