text.skipToContent text.skipToNavigation

Positioning Feedback Cylinders ISO 15552

Series 6PF

Positioning Feedback Cylinders ISO 15552

Series 6PF

Positioning Feedback Cylinders ISO 15552

Series 6PF

In compliance with ISO 15552 standard and with the previous DIN/ISO 6431 - VDMA 24562 standard
Chrome plated steel rod
Protection class IP67
Minimal sliding speed of 5 mm/sec
Minimal sliding pressure < 0,1 bar
G variant for dusty applications (cement, resin, mud, residues from wood, etc...)
ATEX version available

Double-acting low friction, magnetic
ø 50, 63, 80, 100, 125 mm

Series 6PF pneumatic actuators are equipped with a potentiometric linear position transducer integrated inside the rod. This type of cylinder allows, along the entire stroke, a constant control of the rod position which is read processing the change of the transducer internal resistance.
The pistons have been equipped with a permanent magnet which enables the use of external end-stroke sensors.
The dynamic seals are specific for low friction.

Thanks to the electrical connection, realized by means of an M12 male electric round connector positioned on the rear head, these cylinders fulfil the standards of IP67 protection class.
Series 6PF cylinders comply with the ISO 15552 standards and can be assembled with the entire range of standard accessories. They are available with bores from 50mm to 125mm with standard strokes from 50mm to 500mm with intervals of 50mm.
The sturdy design, the flexible installation and the high performance make Series 6PF suitable for use in applications with tensioning cylinders, positioning cylinders and filling, cutting and measuring systems.

Download catalogue

In compliance with ISO 15552 standard and with the previous DIN/ISO 6431 - VDMA 24562 standard
Chrome plated steel rod
Protection class IP67
Minimal sliding speed of 5 mm/sec
Minimal sliding pressure < 0,1 bar
G variant for dusty applications (cement, resin, mud, residues from wood, etc...)
ATEX version available

Purchasable codes

Series

Accessories

there are no salable codes online

If you have entered Filters, try changing them or look in the "Configurator" tab

General Data

GENERAL AND TECHNICAL DATA

PNEUMATIC SECTION
Construction	inner tie-rods
Operation	double-acting low friction, not cushioned
Materials	see the table on the following page
Mountings	front and rear flange foot mounts front / rear / swivel / intermediate trunnion
Bores	50, 63, 80, 100, 125 mm
Strokes min - max	50 ÷ 1000 mm (step 50 mm)
Operating temperature	0°C ÷ 80°C (with dry air -20°C)
Operating pressure	0,1 ÷ 10 bar
Speed (min - max)	5 ÷ 1000 mm/sec (no load)
Max acceleration	10 m/sec²
Fluid	filtered air class 5.4.4 according to ISO 8573-1. If lubricated air is used, it is recommended to use oil ISOVG32. Once applied the lubrication should never be interrupted.
Linearity	0,1% of the stroke
Repeatability	0,03% of the stroke
RESOLUTION	Infinite
Hysteresis	< di 0,5 mm
Vibration test according EN 60068-2-6	severity level 3
Shock test according EN 60068-2-27	severity level 2

ELECTRICAL SECTION
Electrical connection	male connector M12 4 poles IP 67 (EN 60529)
Max input voltage	40 V (stroke 50 mm) 60 V (strokes from 100 to 500 mm)
Max recommended cursor current	< di 0,1 µA
Electrical resistance	5 kohm for strokes from 50 to 300 mm 10 kohm for strokes from 350 to 500 m
Tolerance on resistance	+/- 20%
Max dissipation (40°C)	1 W for stroke 50 mm 2 W for stroke 100 mm 3 W for strokes from 150 to 500 mm
Suitable end-stroke sensors	CST-532 (3 wires) CST-562 (M8)
Suitable M12 connectors	CS-LF04HB (connecteur droit femelle 4 pôles) CS-LR04HB (connecteur femelle à angle droit 4 pôles) CS-LF05HB-D200 (connecteur filaire femelle droit, 5 pôles, 2 mètres) CS-LF05HB-D500 (connecteur filaire femelle droit, 5 pôles, 5 mètres) CS-LR05HB-D200 (connecteur coudé à angle droit, femelle, 5 pôles, 2 mètres) CS-LR05HB-D500 (connecteur filaire femelle à angle droit 5 pôles, 5 mètres) ** la broche n ° 5 ne doit pas être connectée